WILDEN / Pro-Flo X™

WILDEN PX8/PKCPP/TWS/TF/PTV/0502 08-14238 · 2" · Polypropylene · max. 583 L/min · Complete AODD pump

WILDEN item number 08-14238

Nominal port size: 2"
Maximum flow: 583 L/min
Wetted housing: Polypropylene
Diaphragm material: Full Stroke Ptfe, Wil-Flex Back-Up

Review the complete configuration and duty point with DFIN before ordering.

PRODUCT OVERVIEW

Configuration overview

WILDEN PX8/PKCPP/TWS/TF/PTV/0502 is an air-operated double-diaphragm pump configuration organized by DFIN for accurate identification, selection and quotation. The complete code should be used because it defines pump size, wetted construction, air system, elastomers, valve components and special options.

TECHNICAL DATA

Technical parameters

WILDEN item number	08-14238
Model / configuration	PX8/PKCPP/TWS/TF/PTV/0502
Port size	2"
Air distribution system	Pro-Flo X™
Wetted construction	Polypropylene
Diaphragms	Full Stroke Ptfe, Wil-Flex Back-Up
Valve balls	Teflon
Valve seats	PP with Ptfe Encapsulated Viton
Outer piston	Pvdf
Air chamber	Ptfe-Coated Aluminum
Center block	Polypropylene
Air valve	Polypropylene
Maximum capacity (GPM)	154
Maximum capacity (L/min)	583
Weight (kg)	35
Air end repair kit	04-9988-20
Wet end repair kit	08-9805-55-201

Model and configuration explanation

The full WILDEN configuration code identifies size, body and manifold construction, center section, air distribution system, diaphragms, balls, seats and special execution. Similar model families can use different internal parts.

Materials

Review the body, diaphragms, balls, seats, seals and process-fluid compatibility as a complete system. Do not approve a material from one component alone.

Performance

Published maximum flow is a reference value. Actual capacity depends on air supply, discharge pressure, suction condition, viscosity, pipe losses and solids content.

Suitable operating duties

Typical duties include chemical transfer, process circulation, tank unloading, coatings, wastewater and solids-bearing fluids where an AODD pump is appropriate. Final suitability depends on the actual fluid, concentration, temperature and duty point.

Selection guidance

Provide the fluid name and concentration, temperature, viscosity, solids size, suction lift, required flow, discharge pressure, connection standard and available air pressure. For service parts, also provide the pump nameplate and the removed component code where visible.

SERVICE MATCHING

Compatible repair kits and spare parts

AIR END REPAIR KIT

WILDEN 04-9988-20

Air Repair Kit for 1½"-2" Pro-Flo X (PX) Series including PX4, PX400, PX420, PX430, PX8, PX800, PX820, PX830 Clamped and Bolted Pumps with Plastic Air Valve

6 referenced component item numbers

04-3890-03Retaining Ring for 1½" Pumps
08-2620-52Air Valve Gasket in Buna 2" Pro-Flo Shift (PS) Series Pumps
08-3210-55-225Air Valve O-Ring in PTFE 2" Pro-Flo (P), Turbo-Flo (T) Series Pumps
08-3502-52Isolator Gasket in Buna 1½" - 3" Pro-Flo Shift (PS) Series Pumps
04-2390-52-700Wetted Path O-ring in Buna (1.859" ID × 0.139" W)
04-3529-56Center Block Gasket in Hytrel 1½" - 2" Pro-Flo Shift (PS) Series Pumps

WET END REPAIR KIT

WILDEN 08-9805-55-201

Wet End Kit for 2" Original Clamped Plastic including P8, PS8, PX8, PV8, T8 - PTFE/Santoprene® (TWS) Diaphragms, Standard Components

6 referenced component item numbers

08-1040-55Full Stroke PTFE (T_S) diaphragm for 2" clamped pumps
08-1065-57Full Stroke Santoprene® (TWS) back-up diaphragm for 2" pumps
08-1080-55Valve Ball in Ptfe for 2" Pumps
08-1200-60-500Wetted Path O-ring in Teflon Encapsulated FKM (3.750" ID × 0.210" W)
08-1300-60-500Wetted Path O-ring in Teflon Encapsulated FKM (2.225" ID × 0.210" W)
08-9503-99Expanded PTFE Kit for 2" PTFE Tape & Gasket Pumps

Spare Parts for item 08-14238

No official item-specific component list is verified for this configuration yet.

Kit contents and quantities can change by pump generation, material code, special option and revision. DFIN verifies the exact item number and BOM before quotation.

Maintenance notes

Isolate and depressurize both air and fluid lines before service. Inspect diaphragms, valve balls, seats, seals, shaft and air-valve wear together. Follow the applicable WILDEN service manual for assembly sequence, lubrication and fastener torque.

DFIN TECHNICAL DECISION SUPPORT

A practical guide to PX8/PKCPP/TWS/TF/PTV/0502

Use this page as a working product dossier: identify the item, review the duty, verify service relationships and prepare a complete enquiry.

Ask DFIN to verify this record

Confirm the complete build

Use item 08-14238 together with the full model, nameplate and serial number. The complete code controls pump size, wetted materials, air system, elastomers and valve components.

Check the real duty point

Maximum catalog values are not a selected operating point. Confirm required flow, discharge pressure, suction lift, viscosity, temperature, solids and available air pressure.

Review all wetted materials

Assess body, manifolds, diaphragms, balls, seats and seals as one fluid path. Concentration, temperature and cleaning method can change the recommended construction.

Plan the repair package

Match Air Kit, Wet Kit and component codes to the installed revision before shutdown. DFIN can prepare a cross-checked service-parts list from the item number.

MATCHED SERVICE REFERENCES

Parts and kits linked to this product record

Use these records as identification leads. DFIN verifies the exact revision, material and package scope before supply.

Browse all parts & kits →

PRODUCT & SERVICE FAQ

Questions about PX8/PKCPP/TWS/TF/PTV/0502

Answers for identification, selection and service planning. For a confirmed quotation, DFIN checks the complete application and configuration.

Send your item number to DFIN →

How do I confirm WILDEN item 08-14238?

Send the item number, full model, serial number and a clear nameplate photograph. DFIN will compare the construction, air system, elastomers and connection details before quotation.

Are the maximum flow and pressure simultaneous?

Usually not. Maximum values define catalog boundaries. A usable operating point must be selected from the appropriate curve using the real air supply, back pressure and liquid properties.

How are Air Kit and Wet Kit codes matched?

The pump item number, generation, air system and elastomer configuration are checked together. Kit contents and quantities are confirmed for the installed revision before supply.

What should be included in an RFQ?

Provide quantity, fluid and concentration, temperature, viscosity, solids, required flow and pressure, suction condition, connection standard, available air pressure and delivery destination.