WILDEN / Turbo-Flo™

WILDEN T810/WMAAD/NES/NF/MNE/0677 08-13406 · 2" · Cast Iron · max. 640 L/min · Complete AODD pump

WILDEN item number 08-13406

Nominal port size: 2"
Maximum flow: 640 L/min
Wetted housing: Cast Iron
Diaphragm material: Neoprene

Review the complete configuration and duty point with DFIN before ordering.

PRODUCT OVERVIEW

Configuration overview

WILDEN T810/WMAAD/NES/NF/MNE/0677 is an air-operated double-diaphragm pump configuration organized by DFIN for accurate identification, selection and quotation. The complete code should be used because it defines pump size, wetted construction, air system, elastomers, valve components and special options.

TECHNICAL DATA

Technical parameters

WILDEN item number	08-13406
Model / configuration	T810/WMAAD/NES/NF/MNE/0677
Port size	2"
Air distribution system	Turbo-Flo™
Wetted construction	Cast Iron
Diaphragms	Neoprene
Valve balls	Neoprene Flap Valves
Valve seats	Mild steel with Neoprene O-Ring
Outer piston	Mild steel
Air chamber	Aluminum
Center block	Aluminum
Air valve	Brass With Oil Bottle
Maximum capacity (GPM)	169
Maximum capacity (L/min)	640
Weight (kg)	60
Air end repair kit	15-9982-07
Wet end repair kit	08-9834-51

Model and configuration explanation

The full WILDEN configuration code identifies size, body and manifold construction, center section, air distribution system, diaphragms, balls, seats and special execution. Similar model families can use different internal parts.

Materials

Review the body, diaphragms, balls, seats, seals and process-fluid compatibility as a complete system. Do not approve a material from one component alone.

Performance

Published maximum flow is a reference value. Actual capacity depends on air supply, discharge pressure, suction condition, viscosity, pipe losses and solids content.

Suitable operating duties

Typical duties include chemical transfer, process circulation, tank unloading, coatings, wastewater and solids-bearing fluids where an AODD pump is appropriate. Final suitability depends on the actual fluid, concentration, temperature and duty point.

Selection guidance

Provide the fluid name and concentration, temperature, viscosity, solids size, suction lift, required flow, discharge pressure, connection standard and available air pressure. For service parts, also provide the pump nameplate and the removed component code where visible.

SERVICE MATCHING

Compatible repair kits and spare parts

AIR END REPAIR KIT

WILDEN 15-9982-07

Air Repair Kit for Metal 2"-3" Turbo-Flo (T) Series including T810, T1510 Brahma Flap Valve Pumps with Oil Bottle

5 referenced component item numbers

15-2080-07Air Valve Assembly for 3" Turbo-Flo (T) Series with Oil Bottle in Brass
15-2600-52Air Valve Gasket in Buna 3" Turbo-Flo (T) Series Pumps
15-3210-55-225Air Valve O-Ring in PTFE 3" Pro-Flo (P), Turbo-Flo (T) Series, Surge Dampeners Serues Pumps
15-3528-52Center Block Gasket in Buna 3" Brahma (B) Series Pumps
08-3025-52Air Valve O-Ring in Buna 2" Turbo-Flo (T) Series Pumps

WET END REPAIR KIT

WILDEN 08-9834-51

Wet End Kit for 2" Brahma Flap Valve Metal including PS810, PX810, T810 - Neoprene (NES) Diaphragms, Standard Components

5 referenced component item numbers

08-1012-51Brahma Neoprene (NES) diaphragm for 2" pumps
08-1185-51Valve Seat in Neoprene for 2" Pumps
08-1195-51Valve Seat in Neoprene for 2" Pumps
08-1395-51Valve Seat and Gasket Combo in Neoprene 2" Brahma (B) Series Pumps
08-1401-51Manifold Gasket in Neoprene 2" Brahma (B) Series Pumps

Spare Parts for item 08-13406

No official item-specific component list is verified for this configuration yet.

Kit contents and quantities can change by pump generation, material code, special option and revision. DFIN verifies the exact item number and BOM before quotation.

Maintenance notes

Isolate and depressurize both air and fluid lines before service. Inspect diaphragms, valve balls, seats, seals, shaft and air-valve wear together. Follow the applicable WILDEN service manual for assembly sequence, lubrication and fastener torque.

DFIN TECHNICAL DECISION SUPPORT

A practical guide to T810/WMAAD/NES/NF/MNE/0677

Use this page as a working product dossier: identify the item, review the duty, verify service relationships and prepare a complete enquiry.

Ask DFIN to verify this record

Confirm the complete build

Use item 08-13406 together with the full model, nameplate and serial number. The complete code controls pump size, wetted materials, air system, elastomers and valve components.

Check the real duty point

Maximum catalog values are not a selected operating point. Confirm required flow, discharge pressure, suction lift, viscosity, temperature, solids and available air pressure.

Review all wetted materials

Assess body, manifolds, diaphragms, balls, seats and seals as one fluid path. Concentration, temperature and cleaning method can change the recommended construction.

Plan the repair package

Match Air Kit, Wet Kit and component codes to the installed revision before shutdown. DFIN can prepare a cross-checked service-parts list from the item number.

MATCHED SERVICE REFERENCES

Parts and kits linked to this product record

Use these records as identification leads. DFIN verifies the exact revision, material and package scope before supply.

Browse all parts & kits →

PRODUCT & SERVICE FAQ

Questions about T810/WMAAD/NES/NF/MNE/0677

Answers for identification, selection and service planning. For a confirmed quotation, DFIN checks the complete application and configuration.

Send your item number to DFIN →

How do I confirm WILDEN item 08-13406?

Send the item number, full model, serial number and a clear nameplate photograph. DFIN will compare the construction, air system, elastomers and connection details before quotation.

Are the maximum flow and pressure simultaneous?

Usually not. Maximum values define catalog boundaries. A usable operating point must be selected from the appropriate curve using the real air supply, back pressure and liquid properties.

How are Air Kit and Wet Kit codes matched?

The pump item number, generation, air system and elastomer configuration are checked together. Kit contents and quantities are confirmed for the installed revision before supply.

What should be included in an RFQ?

Provide quantity, fluid and concentration, temperature, viscosity, solids, required flow and pressure, suction condition, connection standard, available air pressure and delivery destination.